How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround

Free Estimate



What're your thoughts regarding Installing A Bathtub?


How to Install a Bathtub
Setting up a tub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard job. If the old tub is easily obtainable, the task can relocate quickly; if you need to open up a wall surface to remove the old tub as well as place the new tub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require a helper to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a specialist to take over a halfway-completed job, it is much better to take into consideration using one before you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will assist you mount a new bathtub in your restroom if you have actually already purchased a new bathtub and do not need to alter the plan of your previous water supply pipes.
Your tools and product checklist must make up the following:


  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  •  

Preparing for the Setup


Firstly, the supporting frame provided with the bathroom should be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last setting.



Removing Old Taps


If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted accessibility that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.



Mounting the Bathtub


Making use of the two wood boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the tub until the spirit level checks out level.
To set up taps, fit the bottom of the outermost flexible faucet port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water and also check all joints and also brand-new pipework for leakages and tighten them if necessary. Fill up the tub and additionally inspect the overflow outlet and the typical electrical outlet for leakages.
Ultimately, repair the bath paneling as explained in the supplier's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has been used a minimum of when as this will settle it right into its last setting.



Suitable New Taps


If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in location in between the tap and also the sink. Protect the tap in position with the supplier provided backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind should be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.



Tiling Around the Tub


In the location where the bath fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, causing complications with moisture and possible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealant can crack relatively very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the market. It is recommended to fit the floor tiles using waterproof or water-proof sticky and grout.


Bathtub Installation


How Important Is A Bathtub To Your Home?


High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


Install Piping Before Tub


You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


Position the Tub


Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


Assemble Drain Connections


Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


Place a Pipe For the Shower Head


First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


Attaching Hot and Cold Water Lines


Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


Install the Spout


Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


Check For Leaks


Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


estore the Bathroom Wall


Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


Installing A Bathtub


As an avid person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that excerpt was worth the trouble. Enjoyed our post? Please share it. Help someone else locate it. Thanks for your time spent reading it.




Click On This Link


 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround”

Leave a Reply

Gravatar